CAn someone please let me know if my answers are correct Exercise 1: Constructio

Question

CAn someone please let me know if my answers are correct

Exercise 1: Construction of a Galvanic Cell

Data Table 1. Spontaneous Reaction Observations.

Metal in Solution

Observations

Zinc in Copper Sulfate

Zinc turned black

Copper in Zinc Sulfate

There was no change

Data Table 2. Multimeter Readings.

Time (minutes)

Multimeter Reading (Volts)

0

1.08

15

1.08

30

1.08

45

1.08

60

1.08

75

1.08

90

1.08

105

1.08

120

1.05

135

1.04

Data Table 3. Standard Cell Potential.

Equation

E°(Volts)

Oxidation Half-Reaction

Zn(s) à Zn2+(aq) + 2e-

-.76

Reduction Half-Reaction

Cu2+(aq) + 2e- à Cu(s)

.13

Redox Reaction

Zn(s) + CuSO4(aq) à ZnSO4(aq) + Cu(s)

.89

E cell = 0.13 – (-0.76) = .89

Data Table 4. Galvanic Cell Setup.

Photograph of galvanic cell

Questions

What were the concentrations of the solutions (zinc solution, copper solution, and salt bridge)? Were the concentrations consistent with those of standard state conditions? Explain your answer.

The concentrations of solutions would not be changed if we are taking Zn/ZnSO4 // CusO4/Cu cell. Because how many ions are coming from Zn to ZnSO4. That many ions again reproduced due to an equilibrium reaction. Therefore, all concentrations are - CuSO4 = 1 M, ZnSO4 = 1M

Was the amount of electric energy produced in your galvanic cell consistent with the standard cell potential of the reaction (as calculated in Data Table 3)? Hypothesize why it was or was not consistent.

Yes, the concentrations are consistent throughout the experiment. It was proved by the potential values that occurred in the experiment. The obtained/ galvanic meter values are consistent and supporting, to calculate the values of total cell potentials. If we add, both oxidation and reduction potential values from Data Table 3 we get the cell potential. 0.89 V (0.76+0.13). The amount of energy produced in cell is consistent throughout the experiment and it is proportional to total cell potential.

Was there evidence of electron transfer from the anode to the cathode? Use your data in Data Table 2 to explain your answer.

Yes, the voltage reading increased overtime. If there was no electron transfer from anode to cathode in the cell, then there would not have been any generation of electrical energy. The values of the Galvano meter (Data Table 2) show the electrons are transferring from anode to cathode.

For the following redox reaction in a galvanic cell, write the oxidation half-reaction and the reduction-half reaction, and calculate the standard cell potential of the reaction. Use Table 1 in the Background as needed. Explain how you identified which half-reaction is the oxidizer and which is the reducer. Show all of your work.

Oxidation: Cu(s) à Cu2+(aq) + 2e-   E = 0.34

Reduction: Fe3+(aq) + 1e-à Fe2+(s)   E = 0.77

E cell = 0.77 – 0.34 = 0.43 V

The copper is the oxidizer because it gained two electrons during the reaction. The Iron is the reducer because it lost one electron

Metal in Solution

Observations

Zinc in Copper Sulfate

Zinc turned black

Copper in Zinc Sulfate

There was no change

Explanation / Answer

It seems to be everything is correct, but why suddenly Fe3+, Fe2+ comes in play at last question! May be you have not shown that redox reaction picture! ok

The answer is incorrect for last question. Reason is lower reduction potential metal always behaves as anode means it loses electrons and we say that is reducer.

Correct answer: The copper is the reducer because it loses two electrons during the reaction. The Iron is the oxidizer because it gains one electron.

But you have written Ecell correctly as Ecell = Ecathode - Eanode. the oxidation half-reaction and the reduction-half reaction are correct.

Cathode is iron (reduction happened here means gain of electrons) anode is copper (oxidation happens here means loss of electrons).

Thank You So Much! Please Rate this answer as you wish.

Related Questions

Navigate

• Browse (All)
• Browse C
• Subjects

Integrity-first tutoring: explanations and feedback only — we do not complete graded work. Learn more.