1.Which command can be used to verify route redistribution show summary show ip
ID: 3570336 • Letter: 1
Question
1.Which command can be used to verify route redistribution
show summary
show ip protocol
show redistribution
show ip route
2. T/F The redistribute static command would allow a static route to be advertised to other routers.
3. What is the default metric when redistributing for OSPF?
A. 2.
B. 1
C. 20
D. 10
4. A route _________ can be used to hide certain networks from the rest of the organization.
filter
protocol
table
neighbor
Route filtering can be used to prevent routing loops between autonomous systems.
True
False
6. What is the purpose for using the "ip helper-address" command on a router?
To prevent the router from forwarding broadcasts
To direct BOOTP clients to a BOOTP server
To allow IPX to communicate with IP-base servers
To accommodate compatibility routers using different IP routing protocols
7. What is the purpose for using the "ip helper-address" command on a router?
To prevent the router from forwarding broadcasts
To direct BOOTP clients to a BOOTP server
To allow IPX to communicate with IP-base servers
To accommodate compatibility routers using different IP routing protocols
8. Routes learned via IBGP are always propagated to other IBGP peers.
True
False
9.IBGP peers do not need to be directly connected to their neighbor routers.
True
False
10.Which of the following routes should be received from the ISP to consume as the smallest amount of memory on a router?
only redistributed routes
only internal BGP routes
only partial BGP routes
only default routes
11.
Which BGP command allows eBGP neighbors not on directly connected networks?
ebgp-multihop
weight
send-community
next-hop-self
12.
which command displays iBGP and eBGP neighbors on a BGP enabled router?
show ip bgp sumary
show ip bgp
show ip bgp paths
show ip bgp peers
13.
Assume your company has has BGP connections to multiple ISP's. How could you configure BGP to favor one particular path for outbound traffic?
Enable route reflector
Configure weight
Create a distribute list
none of the above
14. On a Cisco router, which BGP attribute is used first when deterining the best path?
Local preference
AS-Path
Weight
MED
15. When using IGMPv2, the host with the lowest IP address on a subnet is assigned the designated querier role.
True
False
16. Which technology manages traffic at Layer 2 by configuring Layer 2 LAN interfaces dynamically to forward multicast traffic only to those interfaces that want to receive it?
IGMP snooping
MOSPF
DVMRP
RIP
17. PIM sparse mode and PIM sparse-dense mode require an RP on the network when configuring multicast?
True
False
18. Which command is required to configure the IP address of the rendezvous point (RP) located at IP address 10.10.10.1?
ip pim-rp-address 10.10.10.1
ip igmp join group 10.10.10.1
ip pim re-candidate gig0/2
ip pim accept-rep 10.10.10.1
19. IPSec is mandatory and built into IPV6.
True
False
20. Once BGp reaches the __________ state, BGP neighborships are established.
show summary
show ip protocol
show redistribution
show ip route
Explanation / Answer
1.
show summary
2.
True
3.
20
4.
filter
5.
False
6.
To accommodate compatibility routers using different IP routing protocols
7.
To accommodate compatibility routers using different IP routing protocols
8.
True
9.
True.
10.
only internal BGP routes
11.
next-hop-self
12.
show ip bgp peers
13.
Create a distribute list
14.
AS-Path
15.
False
16.
DVMRP
17.
True.
18.
ip pim-rp-address 10.10.10.1
19.
True
20.
Active State
Related Questions
Navigate
Integrity-first tutoring: explanations and feedback only — we do not complete graded work. Learn more.