NEED CISCO CONFIGURATION FOR THE STEPS BELOW Configure a single DHCP pool on WST
ID: 3583108 • Letter: N
Question
NEED CISCO CONFIGURATION FOR THE STEPS BELOW
Configure a single DHCP pool on WST-R1 for the WIRED VLAN 10 network
WST-R1 should never allocate the first 10 IPs or the last 10 IP’s in the subnet o Bring the switch interfaces facing WST-PC2, WST-PC3 and WST-PC4 up o Verify WST-PC2, WST-PC3 and WST-PC4 receive IPv4 and IPv6 addresses o Note: You do not need to configure DHCP for IPv6.
Configure two DHCP pools on EST-R1 for the WIRED and WIRELESS VLANs (10 and 11) o EST-R1 should never allocate the first 10 IPs or the last 10 IP’s in either subnet
Verify EST-PC2 and EST-PC3 receive IPv4 and IPv6 addresses Note: You do not need to configure DHCP for IPv6.
Configure a wireless LAN at the East site o Do not change or configure anything you are not explicitly told to configure o Do not alter the internet or LAN port addressing. They are configured for a reason o Do notenable the DHCP pool on the wireless router.
The SSID should be configured as NETW251 and configured not to broadcast o Configure WPA2 personal security with a PSK of C1sco12345 to secure the network o Leave all other settings on the AP at defaults
Configure EST-PC4 to connect to the wireless network. Verify it receives an IPv4 and IPv6 address
For all routers and switches in the topology complete the following o Save the configuration to NVRAM o Backup the startup-configuration to the TFTP server. The name of the file you upload to the server should always be xxx-confg where xxx is the hostname (for example WST-R1confg)
EAST SITE OSPF AREA 0 EIGRP AS 65535 EST-R1 WEST SITE WST-R1 OSPF AREA 1 WST-PC1 EST-S1 WST-S1 EST-PC1 WST-PC2 Po 1: Fa0/22 -23 Pol: Fa0/ 22-23 EST-PC2 LA, CP PaGP TFTP EST-S2 WST-S2 EST-PC4 WST-PC4. EST-PC3 WST-PC3 EST-AP1Explanation / Answer
Answer :
a single DHCP pool on WST-R1 for the WIRED VLAN 10 network
WST-R1 should never allocate the first 10 IPs or the last 10 IP’s in the subnet o Bring the switch interfaces facing WST-PC2, WST-PC3 and WST-PC4 up o Verify WST-PC2, WST-PC3 and WST-PC4 receive IPv4 and IPv6 addresses o Note: You do not need to configure DHCP for IPv6.
Configure two DHCP pools on EST-R1 for the WIRED and WIRELESS VLANs (10 and 11) o EST-R1 should never allocate the first 10 IPs or the last 10 IP’s in either subnet
Verify EST-PC2 and EST-PC3 receive IPv4 and IPv6 addresses Note: You do not need to configure DHCP for IPv6.
Configure a wireless LAN at the East site o Do not change or configure anything you are not explicitly told to configure o Do not alter the internet or LAN port addressing. They are configured for a reason o Do notenable the DHCP pool on the wireless router.
The SSID should be configured as NETW251 and configured not to broadcast o Configure WPA2 personal security with a PSK of C1sco12345 to secure the network o Leave all other settings on the AP at defaults
Configure EST-PC4 to connect to the wireless network. Verify it receives an IPv4 and IPv6 address
For all routers and switches in the topology complete the following o Save the configuration to NVRAM o Backup the startup-configuration to the TFTP server. The name of the file you upload to the server should always be xxx-confg where xxx is the hostname (for example WST-R1confg)
Related Questions
Navigate
Integrity-first tutoring: explanations and feedback only — we do not complete graded work. Learn more.